Configure centralized logging from text log files in Unix with remote_syslog2. Use
remote_syslog2 to aggregate logs from any text file, like app log files, in Unix and BSD.
To send log files to Papertrail from applications and daemons that don't support syslog, run Papertrail's tiny standalone remote_syslog2 daemon. It tracks one or more log files and sends new entries to Papertrail in realtime.
remote_syslog2 works for any text log files, has no impact to or reliance on the system syslog daemon or its logging configuration, is easy to set up, and forwards logs directly to Papertrail. No adjustments to
syslog-ng.conf are required.
Some applications that typically log to text files, such as MySQL, Apache, and Tomcat (log4j), have internal support for logging directly to syslog. For apps like these, either their internal syslog or
remote_syslog2 can be used to send logs to Papertrail.
remote_syslog2 can be deployed and configured with configuration management tools. Papertrail provides official support for Chef, Puppet, and Salt:
These configuration management modules only configure and deploy
remote_syslog2. To configure and manage the system’s syslog daemon configuration, see Configuring remote syslog from Unix/Linux and BSD/macOS.
Download the current release. To extract it and copy the binary into a system path, run:
$ tar xzf ./remote_syslog*.tar.gz
$ cd remote_syslog
$ sudo cp ./remote_syslog /usr/local/bin
RPM and Debian packages are also available.
Paths to log file(s) can be specified on the command-line, or save log_files.yml.example as
/etc/log_files.yml. Edit it to define:
- the path to this app's log file, and any other log file(s) to watch.
- the destination
portprovided under log destinations. If no destination port was provided, set
logs.papertrailapp.comand remove the
portconfig line to use the default port (514).
Start the daemon:
$ sudo remote_syslog
Logs should appear in Papertrail within a few seconds of being written to the on-disk log file. Problem? See Troubleshooting.
remote_syslog requires read permission on the log files it is monitoring.
remote_syslog2 is daemonized as
remote_syslog. When you’re looking for the process, look for
Install an init file.
Please feel free to contact us, either instead of following these instructions or while trying them. We enjoy helping, and these steps are only here if they let you save time by troubleshooting independently.
There are a few reasons
remote_syslog might not be sending logs.
ps auxww | grep [r]emote_syslog. Exactly one process should be shown, like this:
root 24501 0.0 0.4 13952 8864 ? S Mar01 2:45 remote_syslog
In the example above, the process is running as user
root. If a user other than
root is shown, does that user running
remote_syslog have permission to write to
/var/run/ is the default location for PID files (background).
remote_syslog isn’t already running as root, try running it as root to test (such as with
sudo), or specify an alternate location for the PID file (such as with
remote_syslog starts but subsequently stops running, try leaving it attached to the terminal (rather than daemonizing) using
remote_syslog is running, try stopping it and restarting it manually in the foreground, logging at
DEBUG level, with:
$ remote_syslog -D --log="<root>=DEBUG"
After it starts, it'll print detailed logs about its activity to the terminal. If it's unable to connect, check Troubleshooting reachability. If it’s unable to forward one or more of the log files, (for example, if it prints
Cannot forward filename.log, it may not exist), check the filenames and permissions.
After the initial message
Forwarding file: filename.log, it’s normal for
remote_syslog to print
Skipping filename.log because it is already running on subsequent checks of the currently watched files.
remote_syslog only reads new additions to the log files after it was started. If there’s no new activity, no logs will appear in Papertrail. To check whether a file is active, run:
$ tail -Fn0 filename.log
to watch for new lines coming in; this is very similar to what
remote_syslog2 does. To verify that new lines would be sent once added, try:
$ echo "Papertrail test line" >> filename.log
If that line appears, any new lines added to the log will also appear in Papertrail.
…perhaps across many systems at the same time? This could be a firewall policy change or log rotation. However,
remote_syslog plays well with all common log rotation systems (with no changes to the configuration of either), so we’d like to hear about this problem.
If so, enable polling via the
$ strace -tt -s 500 -fp 12345
12345 is the process ID of
remote_syslog, obtained from the second column of
ps auxww. This will output every call that it makes. We suggest sending the strace output to a file:
$ strace -tt -s 500 -fp 12345 -o strace.log
Feel free to send the
strace.log file to us via firstname.lastname@example.org. We’ll look for a few things. Did the OS notify
remote_syslog of writes to the log files? Did
sendto() (UDP) or
send() (TCP) to try sending the message? What happened?
See other options with:
$ remote_syslog --help
See also Troubleshooting reachability.
Can we help? Just ask.
The scripts are not supported under any SolarWinds support program or service. The scripts are provided AS IS without warranty of any kind. SolarWinds further disclaims all warranties including, without limitation, any implied warranties of merchantability or of fitness for a particular purpose. The risk arising out of the use or performance of the scripts and documentation stays with you. In no event shall SolarWinds or anyone else involved in the creation, production, or delivery of the scripts be liable for any damages whatsoever (including, without limitation, damages for loss of business profits, business interruption, loss of business information, or other pecuniary loss) arising out of the use of or inability to use the scripts or documentation.